NinajaBlocks / BeagleBone boot problem

SD/MMC found on device 0
reading uEnv.txt

723 bytes read
Loaded environment from uEnv.txt
Importing environment from mmc ...
reading uImage

2622984 bytes read
reading uInitrd

2938135 bytes read
Booting from mmc ...
## Booting kernel from Legacy Image at 80300000 ...
Image Name: 3.2.18-psp14
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2622920 Bytes = 2.5 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81600000 ...
Image Name: initramfs
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 2938071 Bytes = 2.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.18-psp14 (root@panda-es-b1-1gb) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #1 Sat Jun 9 05:26:22 UTC 2012
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: am335xevm
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] AM335X ES1.0 (sgx neon )
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyO0,115200n8 VIDEO_DISPLAY root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait fixrtc ip=none
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] allocated 1048576 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 248448k/248448k available, 13696k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc068d000 (6676 kB)
[ 0.000000] .init : 0xc068d000 - 0xc06cb000 ( 248 kB)
[ 0.000000] .data : 0xc06cc000 - 0xc0713ee0 ( 288 kB)
[ 0.000000] .bss : 0xc0713f04 - 0xc0755858 ( 263 kB)
[ 0.000000] NR_IRQS:410 nr_irqs:410 410
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[ 0.000000] Total of 128 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz
[ 0.000000] omap_dm_timer_switch_src: Switching to HW default clocksource(sys_clkin_ck) for timer1, this may impact timekeeping in low power state
[ 0.000000] OMAP clocksource: GPTIMER1 at 24000000 Hz
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000260] Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464)
[ 0.116358] pid_max: default: 32768 minimum: 301
[ 0.116521] Security Framework initialized
[ 0.116600] AppArmor: AppArmor initialized
[ 0.116668] Mount-cache hash table entries: 512
[ 0.117153] Initializing cgroup subsys cpuacct
[ 0.117203] Initializing cgroup subsys memory
[ 0.117254] Initializing cgroup subsys devices
[ 0.117271] Initializing cgroup subsys freezer
[ 0.117287] Initializing cgroup subsys blkio
[ 0.117316] Initializing cgroup subsys perf_event
[ 0.117419] CPU: Testing write buffer coherency: ok
[ 0.118635] devtmpfs: initialized
[ 0.139649] omap_hwmod: gfx: failed to hardreset
[ 0.156530] omap_hwmod: pruss: failed to hardreset
[ 0.157448] print_constraints: dummy:
[ 0.157767] NET: Registered protocol family 16
[ 0.159172] OMAP GPIO hardware version 0.1
[ 0.160547] omap_mux_init: Add partition: #1: core, flags: 0
[ 0.162188] omap_i2c.1: alias fck already exists
[ 0.162671] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.162899] omap2_mcspi.1: alias fck already exists
[ 0.163040] omap2_mcspi.2: alias fck already exists
[ 0.163157] omap_init_sham: platform not supported
[ 0.163173] omap_init_aes: platform not supported
[ 0.163268] edma.0: alias fck already exists
[ 0.163296] edma.0: alias fck already exists
[ 0.163323] edma.0: alias fck already exists
[ 0.163426] cape: pcm register
[ 0.173619] bio: create slab at 0
[ 0.175331] SCSI subsystem initialized
[ 0.176465] usbcore: registered new interface driver usbfs
[ 0.176628] usbcore: registered new interface driver hub
[ 0.176837] usbcore: registered new device driver usb
[ 0.177228] registerd cppi-dma Intr @ IRQ 17
[ 0.177250] Cppi41 Init Done Qmgr-base(d083a000) dma-base(d0838000)
[ 0.177265] Cppi41 Init Done
[ 0.177300] musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3
[ 0.177487] musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1
[ 0.178086] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz
[ 0.179009] tps65910 1-002d: could not be detected
[ 0.179643] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.180333] NetLabel: Initializing
[ 0.180351] NetLabel: domain hash size = 128
[ 0.180363] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.180439] NetLabel: unlabeled traffic allowed by default
[ 0.180487] Switching to clocksource gp timer
[ 0.180761] AppArmor: AppArmor Filesystem Enabled
[ 0.194333] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[ 0.194550] musb-hdrc musb-hdrc.0: dma type: dma-cppi41
[ 0.194767] MUSB0 controller's USBSS revision = 4ea20800
[ 0.195700] musb-hdrc musb-hdrc.0: USB OTG mode controller at d081c000 using DMA, IRQ 18
[ 0.196045] musb-hdrc musb-hdrc.1: dma type: dma-cppi41
[ 0.196232] MUSB1 controller's USBSS revision = 4ea20800
[ 0.196741] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[ 0.196862] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1
[ 0.197035] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.197059] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.197080] usb usb1: Product: MUSB HDRC host driver
[ 0.197097] usb usb1: Manufacturer: Linux 3.2.18-psp14 musb-hcd
[ 0.197114] usb usb1: SerialNumber: musb-hdrc.1
[ 0.197920] hub 1-0:1.0: USB hub found
[ 0.197959] hub 1-0:1.0: 1 port detected
[ 0.198557] musb-hdrc musb-hdrc.1: USB Host mode controller at d081e800 using DMA, IRQ 19
[ 0.199086] NET: Registered protocol family 2
[ 0.199477] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.200639] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.200867] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.201005] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.201024] TCP reno registered
[ 0.201042] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.201076] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.201498] NET: Registered protocol family 1
[ 0.201991] RPC: Registered named UNIX socket transport module.
[ 0.202014] RPC: Registered udp transport module.
[ 0.202028] RPC: Registered tcp transport module.
[ 0.202041] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.202346] Trying to unpack rootfs image as initramfs...
[ 0.557553] Freeing initrd memory: 2868K
[ 0.559775] audit: initializing netlink socket (disabled)
[ 0.559874] type=2000 audit(0.550:1): initialized
[ 0.779587] VFS: Disk quotas dquot_6.5.2
[ 0.779742] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.781827] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.781907] fuse init (API version 7.17)
[ 0.782730] Btrfs loaded
[ 0.782770] msgmni has been set to 490
[ 0.784260] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.784399] io scheduler noop registered
[ 0.784416] io scheduler deadline registered
[ 0.784505] io scheduler cfq registered (default)
[ 0.785855] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.787318] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0
[ 1.513137] console [ttyO0] enabled
[ 1.517077] usb 1-1: new high-speed USB device number 2 using musb-hdrc
[ 1.524681] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1
[ 1.532599] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2
[ 1.540428] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3
[ 1.548298] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4
[ 1.556153] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5
[ 1.573211] brd: module loaded
[ 1.581577] loop: module loaded
[ 1.584982] at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[ 1.650541] No daughter card found
[ 1.654178] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[ 1.662877] usb 1-1: New USB device found, idVendor=0bda, idProduct=8176
[ 1.669952] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.677484] usb 1-1: Manufacturer: Realtek
[ 1.681810] usb 1-1: SerialNumber: 00e04c000001
[ 1.692765] Board config.name: A335BONE00A62113BB000975
[ 1.698272] Board name: A335BONE
[ 1.701695] Board version: 00A6
[ 1.704997] The board is a AM335x Beaglebone.
[ 1.710277] tps65217 1-0024: TPS65217 ID 0xf version 1.2
[ 1.717826] print_constraints: DCDC1: 900 <--> 1800 mV at 1800 mV
[ 1.726332] print_constraints: DCDC2: 900 <--> 3300 mV at 1275 mV
[ 1.734790] print_constraints: DCDC3: 900 <--> 1500 mV at 1100 mV
[ 1.743247] print_constraints: LDO1: 1000 <--> 3300 mV at 1800 mV
[ 1.751675] print_constraints: LDO2: 900 <--> 3300 mV at 3300 mV
[ 1.760021] print_constraints: LDO3: 1800 <--> 3300 mV at 3300 mV
[ 1.768484] print_constraints: LDO4: 1800 <--> 3300 mV at 3300 mV
[ 1.775536] Disabling OPP for 275MHz due to silicon errata
[ 1.781214] Maximum current provided by the USB port is 500mA which is not sufficient
[ 1.781229] when operating @OPP120 and OPPTURBO. The current requirement for some
[ 1.781241] use-cases using OPP100 might also exceed the maximum current that the
[ 1.781254] USB port can provide. Unless you are fully confident that the current
[ 1.781266] requirements for OPP100 use-case don't exceed the USB limits, switching
[ 1.781278] to AC power is recommended.
[ 1.825728] omap_i2c.3: alias fck already exists
[ 1.831021] omap_i2c omap_i2c.3: bus 3 rev2.4.0 at 100 kHz
[ 1.837787] omap_hsmmc.0: alias fck already exists
[ 1.847009] at24 3-0054: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[ 1.910545] BeagleBone cape EEPROM: could not read eeprom at address 0x54
[ 1.917741] at24 3-0055: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[ 1.980542] BeagleBone cape EEPROM: could not read eeprom at address 0x55
[ 1.987755] at24 3-0056: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[ 2.050725] BeagleBone cape EEPROM: could not read eeprom at address 0x56
[ 2.057925] at24 3-0057: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[ 2.120542] BeagleBone cape EEPROM: could not read eeprom at address 0x57
[ 2.127683] BeagleBone cape: exporting ADC pins to sysfs
[ 2.133700] Beaglebone: initializing onboard LEDs
[ 2.138677] BeagleBone cape: exporting SPI pins as spidev
[ 2.144976] BeagleBone cape: initializing w1-gpio
[ 2.150074] w1-gpio connected to P8_6
[ 2.155055] CAN device driver interface
[ 2.159093] CAN bus driver for Bosch D_CAN controller 1.0
[ 2.210560] davinci_mdio davinci_mdio.0: davinci mdio revision 1.6
[ 2.217069] davinci_mdio davinci_mdio.0: detected phy mask fffffffe
[ 2.232194] davinci_mdio.0: probed
[ 2.235798] davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver SMSC LAN8710/LAN8720
[ 2.244667] usbcore: registered new interface driver cdc_ether
[ 2.250914] usbcore: registered new interface driver rndis_host
[ 2.257187] cdc_ncm: 04-Aug-2011
[ 2.260685] usbcore: registered new interface driver cdc_ncm
[ 2.266720] Initializing USB Mass Storage driver...
[ 2.272074] usbcore: registered new interface driver usb-storage
[ 2.278392] USB Mass Storage support registered.
[ 2.283430] usbcore: registered new interface driver libusual
[ 2.289585] gadget: using random self ethernet address
[ 2.295126] gadget: using random host ethernet address
[ 2.301761] usb0: MAC 16:b5:4c:06:6b:af
[ 2.305798] usb0: HOST MAC 92:f5:51:94:eb:84
[ 2.310348] gadget: Ethernet Gadget, version: Memorial Day 2008
[ 2.316720] gadget: g_ether ready
[ 2.320315] musb-hdrc musb-hdrc.0: MUSB HDRC host driver
[ 2.326005] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 2
[ 2.333948] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.341120] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.348717] usb usb2: Product: MUSB HDRC host driver
[ 2.353956] usb usb2: Manufacturer: Linux 3.2.18-psp14 musb-hcd
[ 2.360182] usb usb2: SerialNumber: musb-hdrc.0
[ 2.365774] hub 2-0:1.0: USB hub found
[ 2.369741] hub 2-0:1.0: 1 port detected
[ 2.375027] mousedev: PS/2 mouse device common for all mice
[ 2.382178] omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0
[ 2.388975] i2c /dev entries driver
[ 2.393224] Linux media interface: v0.10
[ 2.397521] lirc_dev: IR Remote Control driver registered, major 249
[ 2.404328] Driver for 1-wire Dallas network protocol.
[ 2.411246] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 2.419237] cpuidle: using governor ladder
[ 2.423800] cpuidle: using governor menu
[ 2.432138] usbcore: registered new interface driver snd-usb-6fire
[ 2.439291] ALSA device list:
[ 2.442487] No soundcards found.
[ 2.447432] TCP cubic registered
[ 2.451116] NET: Registered protocol family 10
[ 2.459327] NET: Registered protocol family 17
[ 2.464282] can: controller area network core (rev 20090105 abi 8)
[ 2.470972] NET: Registered protocol family 29
[ 2.475652] can: raw protocol (rev 20090105)
[ 2.480205] Registering the dns_resolver key type
[ 2.485253] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[ 2.493345] ThumbEE CPU extension supported.
[ 2.497909] mux: Failed to setup hwmod io irq -22
[ 2.503724] Power Management for AM33XX family
[ 2.514202] registered taskstats version 1
[ 2.518885] Detected MACID=bc:6a:29:c4:a0:c0
[ 2.526668] omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 2.536742] Freeing init memory: 248K
Loading, please wait...
[ 2.613342] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 2.630814] mmc0: new high speed SDHC card at address 1234
[ 2.642971] mmcblk0: mmc0:1234 SA04G 3.63 GiB
[ 2.662388] mmcblk0: p1 p2
[ 2.738544] udevd[67]: starting version 175
Begin: Loading essential drivers ... [ 2.781520] gadget: high-speed config #1: CDC Ethernet (ECM)
done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... hwclock: select() to /dev/rtc0 to wait for clock tick timed out: No such file or directory
done.
[ 9.565969] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem
[ 9.573724] EXT4-fs (mmcblk0p2): write access will be enabled during recovery
[ 13.732489] mmcblk0: error -110 transferring data, sector 3547720, nr 128, cmd response 0x900, card status 0x200b00
[ 13.743845] mmcblk0: retrying using single block read
[ 17.779677] mmcblk0: error -110 transferring data, sector 3547780, nr 68, cmd response 0x900, card status 0x0
[ 17.790200] end_request: I/O error, dev mmcblk0, sector 3547780
[ 21.701657] mmcblk0: error -110 transferring data, sector 3547782, nr 66, cmd response 0x900, card status 0x0
[ 21.712177] end_request: I/O error, dev mmcblk0, sector 3547782
[ 25.609588] mmcblk0: error -110 transferring data, sector 3547783, nr 65, cmd response 0x900, card status 0x0
[ 25.620108] end_request: I/O error, dev mmcblk0, sector 3547783
[ 25.626474] JBD2: Failed to read block at offset 848
[ 25.640538] JBD2: recovery failed
[ 25.644033] EXT4-fs (mmcblk0p2): error loading journal
[ 29.517854] mmcblk0: error -110 transferring data, sector 3547784, nr 64, cmd response 0x900, card status 0x0
[ 29.528390] end_request: I/O error, dev mmcblk0, sector 3547784
[ 33.426641] mmcblk0: error -110 transferring data, sector 3547785, nr 63, cmd response 0x900, card status 0x0
[ 33.437167] end_request: I/O error, dev mmcblk0, sector 3547785
[ 36.258347] mmcblk0: error -110 transferring data, sector 3547787, nr 61, cmd response 0x900, card status 0x0
[ 36.268868] end_request: I/O error, dev mmcblk0, sector 3547787
[ 40.166888] mmcblk0: error -110 transferring data, sector 3547788, nr 60, cmd response 0x900, card status 0x0
[ 40.177408] end_request: I/O error, dev mmcblk0, sector 3547788
[ 44.075930] mmcblk0: error -110 transferring data, sector 3547789, nr 59, cmd response 0x900, card status 0x0
[ 44.086452] end_request: I/O error, dev mmcblk0, sector 3547789
[ 47.984358] mmcblk0: error -110 transferring data, sector 3547790, nr 58, cmd response 0x900, card status 0x0
[ 47.994878] end_request: I/O error, dev mmcblk0, sector 3547790
[ 51.916647] mmcblk0: error -110 transferring data, sector 3547792, nr 56, cmd response 0x900, card status 0x0
[ 51.927170] end_request: I/O error, dev mmcblk0, sector 3547792
[ 55.824860] mmcblk0: error -110 transferring data, sector 3547793, nr 55, cmd response 0x900, card status 0x0
[ 55.835380] end_request: I/O error, dev mmcblk0, sector 3547793
[ 59.733023] mmcblk0: error -110 transferring data, sector 3547794, nr 54, cmd response 0x900, card status 0x0
[ 59.743542] end_request: I/O error, dev mmcblk0, sector 3547794
[ 63.641464] mmcblk0: error -110 transferring data, sector 3547795, nr 53, cmd response 0x900, card status 0x0
[ 63.651983] end_request: I/O error, dev mmcblk0, sector 3547795
[ 67.549923] mmcblk0: error -110 transferring data, sector 3547796, nr 52, cmd response 0x900, card status 0x0
[ 67.560443] end_request: I/O error, dev mmcblk0, sector 3547796
[ 71.458384] mmcblk0: error -110 transferring data, sector 3547797, nr 51, cmd response 0x900, card status 0x0
[ 71.468904] end_request: I/O error, dev mmcblk0, sector 3547797
[ 75.366979] mmcblk0: error -110 transferring data, sector 3547798, nr 50, cmd response 0x900, card status 0x0
[ 75.377499] end_request: I/O error, dev mmcblk0, sector 3547798
[ 79.292307] mmcblk0: error -110 transferring data, sector 3547800, nr 48, cmd response 0x900, card status 0x0
[ 79.302827] end_request: I/O error, dev mmcblk0, sector 3547800
[ 82.105340] mmcblk0: error -110 transferring data, sector 3547801, nr 47, cmd response 0x900, card status 0x0
[ 82.115860] end_request: I/O error, dev mmcblk0, sector 3547801
[ 86.013839] mmcblk0: error -110 transferring data, sector 3547802, nr 46, cmd response 0x900, card status 0x0
[ 86.024359] end_request: I/O error, dev mmcblk0, sector 3547802
[ 89.942346] mmcblk0: error -110 transferring data, sector 3547804, nr 44, cmd response 0x900, card status 0x0
[ 89.952865] end_request: I/O error, dev mmcblk0, sector 3547804
[ 93.850707] mmcblk0: error -110 transferring data, sector 3547805, nr 43, cmd response 0x900, card status 0x0
[ 93.861226] end_request: I/O error, dev mmcblk0, sector 3547805
[ 97.759154] mmcblk0: error -110 transferring data, sector 3547806, nr 42, cmd response 0x900, card status 0x0
[ 97.769676] end_request: I/O error, dev mmcblk0, sector 3547806
[ 101.667752] mmcblk0: error -110 transferring data, sector 3547807, nr 41, cmd response 0x900, card status 0x0
[ 101.678271] end_request: I/O error, dev mmcblk0, sector 3547807
mount: mounting /dev/mmcblk0p2 on /root failed: Invalid argument
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... mount: mounting /dev on /root/dev failed: No such file or directory
done.
mount: mounting /sys on /root/sys failed: No such file or directory
mount: mounting /proc on /root/proc failed: No such file or directory
Target filesystem doesn't have requested /sbin/init.
No init found. Try passing init= bootarg.
s.

(initramfs)